Watchfire General MxAnalytics Settings

Open Help with keyword "videomotionanalysis"

MOBOTIX M25 Watchfire General MxAnalytics Settings

General Settings	Value	Explanation
Arming		Arm MxAnalytics: Controls image analysis: Enabled: activate image analysis. Off: deactivate image analysis. SI: Image analysis armed by signal input. CS: Image analysis armed by custom signal as defined in General Event Settings.
		Time Table Profile: Time table profile for time-controlled image analysis. (Time Tables)
		Low-Light Suppression: Disables analysis if illumination drops below selected value.
MxAnalytics storage is not activated. Please activate storage and reboot in order to use MxAnalytics export functionality. Make sure that the device is formatted accordingly. If not, you should format it here first.
Detection Settings	Value	Explanation
Detection Area		Detection Area Definitions: Format: lens, window lens: 0=right, 1=left. window: can be defined as a rectangle as well as a polygon. For a detailed description of window definitions and additional variables, please refer to the help page. Note: If no detection area is provided, the camera determines the area autonomously. Note: All user-defined coordinates are relative to the entire sensor area. The origin (0,0) corresponds to the lower left corner, (1279,959) to the upper right corner (if the image is mirrored/rotated the coordinate system changes accordingly). *Detection areas can also be defined by Shift-click+click in the live image and pressing Add detection area.*
	Show Detection Area
Mounting Height		Mounting Height: Mounting height of the camera [150..1000 cm].
Tilt Angle		Tilt angle of the camera.: Configure the tilt angle of the camera in degrees. Installation on/in the ceiling corresponds to -90°, installation on/in the wall corresponds to 0°.
Minimum Object Size		Minimum Object Size: Minimum size of objects in pixels [250..250000]. The size can also be defined by setting a rectangle inside the outline of the object to be detected. *The minimum object size can also be defined by Shift-click+click in the live image and pressing Set minimum object size.*
Light and Shadow		Light and Shadow: The quality of the analysis depends on the light and shadow conditions in the detection areas. Select one of the predefined setups or configure a custom setup.
	Constant illumination Slowly changing illumination Fast changing illumination	Illumination Conditions: The quality of the analysis also depends on how illumination changes. Note that "Constant illumination" and "Slowly changing illumination" allow further adjustment of shadow detection.
	Coarse structure/dark background Fine structure/light background	Shadow Detection: Depending on the light and shadow conditions, shadow detection can be adjusted further.
		Shadow Detection Sensitivity: Set the level of sensitivity for shadow detection on fine structures or light background.
Sensitivity		Detection Sensitivity: The higher the value, the greater the difference between the object and the background has to be in order to be detected [1..100]. This option has no effect when using the "Heavy sunlight, well-defined shadows" or the "Fast changing illumination" settings.
Object Display Settings	Value	Explanation
Bounding Box		Bounding Box Color: Enable visualization of bounding boxes by selecting a color.
Object Track		Object Track Color: Enable visualization of object tracks by selecting a color.
Object Halo		Object Halo Color: Enable visualization of object halos by selecting a color.
		Transparency: Set the transparency of the object halos [0..100%].
Counting Corridor Settings	Value	Explanation
Counting Corridors	0,start=800x440,end=800x520,width=360,id=1,name=Corridor 1	Configure counting corridors: Format: lens,start=point,end=point,width=width lens: 0=right, 1=left. start: starting point of corridor (direction). end: ending point of corridor (direction). point: x coordinate x y coordinate. width: width of the corridor. For a detailed description of corridor definitions and additional variables, please refer to the help page.
Alarm and Counting Corridors		Alarm and Counting Corridor Style: Appearance of alarm and counting corridor.
		Counting Corridor Color: Select color used for the counting corridors. A corridor is highlighted using the complementary color.
		Text Color: Select color used for the corridor IDs.
		Counter "North" Color: Select color used for the counting values in arrow direction.
		Counter "South" Color: Select color used for the counting values against the arrow direction.
	Show Counting Corridor IDs	Counting Corridor IDs: The corridor IDs will be shown at the bottom of each corridor.
	Show Counter Values	Counter Values: Counter values will be shown next to the center of each corridor.
Heatmap Settings	Value	Explanation
Reference Image		Save Reference Image: Click to save the current image as reference image for heatmap reports.
		Show Reference Image: Click to show the current reference image.
		Delete Reference Image: Click to delete the current reference image.
Live Image Display	Show Heatmap	Show Heatmap in Image: Shows the heatmap since the last reset of MxAnalytics in the live image and in the recordings.
		Minimum Value: Set minimum value to visualize in percent. The current minimum value will be used, if 0 is selected.
		Maximum Value: Set maximum value to visualize in percent.
	Show Legend	Legend: Displays the legend of the heatmap.